b72acfa648
It seems that Raspberry Pi OS by default applies an overlay for Raspberry Pi 4. Apply this change to the HAOS config.txt as well.
82 lines
2.0 KiB
Plaintext
82 lines
2.0 KiB
Plaintext
# For more options and information see
|
|
# http://rpf.io/configtxt
|
|
# Some settings may impact device functionality. See link above for details
|
|
|
|
# HAOS - don't change it!
|
|
disable_splash=1
|
|
kernel=u-boot.bin
|
|
|
|
# uncomment for aarch64 bit support
|
|
#arm_64bit=1
|
|
|
|
# uncomment to enable primary UART console
|
|
#enable_uart=1
|
|
|
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# uncomment this if your display has a black border of unused pixels visible
|
|
# and your display can output without overscan
|
|
#disable_overscan=1
|
|
|
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
#overscan_left=16
|
|
#overscan_right=16
|
|
#overscan_top=16
|
|
#overscan_bottom=16
|
|
|
|
# uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# uncomment if hdmi display is not detected and composite is being output
|
|
#hdmi_force_hotplug=1
|
|
|
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
|
#hdmi_group=1
|
|
#hdmi_mode=1
|
|
|
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
# Uncomment to disable continous SD-card poll (for USB SSD)
|
|
#dtparam=sd_poll_once=on
|
|
|
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
#dtparam=i2c_arm=on
|
|
#dtparam=i2s=on
|
|
#dtparam=spi=on
|
|
|
|
# Uncomment this to enable the lirc-rpi module
|
|
#dtoverlay=lirc-rpi
|
|
|
|
# Uncomment this to enable GPIO support for RPI-RF-MOD/HM-MOD-RPI-PCB
|
|
#enable_uart=1
|
|
#dtparam=i2c_arm=on
|
|
#dtoverlay=miniuart-bt
|
|
#dtoverlay=rpi-rf-mod
|
|
|
|
# Additional overlays and parameters are documented /boot/overlays/README
|
|
|
|
# Enable audio (loads snd_bcm2835)
|
|
dtparam=audio=on
|
|
|
|
[pi4]
|
|
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
|
|
dtoverlay=vc4-fkms-v3d
|
|
max_framebuffers=2
|
|
|
|
[all]
|
|
#dtoverlay=vc4-fkms-v3d
|
|
#max_framebuffers=2
|