* Add squashfs with LZ4 and LZO compression to Barebox
* Add squashfs with LZO compression to U-Boot
* Use squashfs for Linux kernel partition
Generate a squashfs image with LZO compression for the Linux kernel
partition. Adjust the boot scripts to be file system independent commands
to boot from squashfs.
* add eq3_char_loop package (eQ-3 char loopback kernel module)
* add generic_raw_uart package (low-latency raw UART kernel driver)
* add rpi-rf-mod package
* add device tree overlay support for RPI-RF-MOD/HM-MOD-RPI-PCB on Raspberry Pi
* enable GPIOLIB and GPIO_SYSFS required for RPI-RF-MOD/HM-MOD-RPI-PCB support.
* add basic RPI-RF-MOD/HM-MOD-RPI-PCB support for ASUS Tinker Board
* add device tree overlay support for ASUS Tinker Board and add
haos-config.txt loading support to U-Boot boot script
* Re-add patches missed with U-Boot 2021.04-rc4 upgrade
Also add patches for Raspberry Pi again.
* Regenerate patches for U-Boot 2021.04
* Update to U-Boot 2021.04
Bump to the latest U-Boot release 2021.04-rc4. This alows to drop quite
some patches which have been sent to the mailing list or picked from the
mailing list and have been merged upstream now.
* Add Ralink rt27xx/rt28xx/rt30xx firmware (#1242)
Add Ralink firmware for devices which have the driver enabled. The
firmware's are rather small at 20KiB in total.
* Remove Ralink and other WiFi drivers from Tinker Board
The board has on-board WiFi, no need for Ralink drivers to be enabled.
* Add Ralink WiFi drivers and firmware to ODROID boards
* Improve ASUS Tinker Board support for 5.10
Remove patches which are unnecessary. Revert DMA for UART as it seems to
cause more problems (its also what Armbian is doing). With that
Bluetooth firmware seems to load without errors when loaded before the
bluetooth daemon is running!
Note: It seems that the board overheats quite quickly. With Armbian,
without load, that seems not to be a big deal, but HAOS does quite a
bunch at startup, leading the CPU to reach the 90°C trip point. Maybe it
was related to the rather closed shelf I have the ASUS Tinker board
running, but only after using a fan the board behaved for me.
* Use hardware flow control explicitly
The rtk_hciattach program uses hardware flow control by default (judging
from tty settings after starting the program). Just to be sure,
explicitly request 115200 and hardware flow control.
* Drop ODROID specific kernel update script
With the jump to Linux 5.10 LTS we can use the same upstream kernel for
Hardkernel ODROID boards as well. Extend the update-kernel-upstream.sh
to support the ODROID boards.
* Linux: Update kernel 5.10.13
* Avoid trying to boot non-existing kernel image in fail-over case
The A/B update system automatically switches to the other boot slot when
booting fails. However, in a fresh installation, only boot slot A
exists. If booting fails three times (e.g. if somebody plugs out power
before the slot can be marked as good), then the system switches to boot
slot B which does not contain a kernel image yet. Avoid trying to boot
the non-existing kernel image.
With this change, if slot B is empty U-Boot will restore both slots to 3
attempts and retry booting from slot A on next reboot:
```
Trying to boot slot B, 2 attempts remaining. Loading kernel ...
** Unrecognized filesystem type **
No valid slot found, resetting tries to 3
storing env...
```
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
* Remove rk3288-xt-q8l-v10.dts related patches
We only support ASUS Tinker Board, so no need for those patches.
* Remove unnecessary patches and rebase some for Tinker Board S
Some patches only apply to the Tinker Board device tree. Rebase them to
apply to the dtsi file so they apply for both boards, the Tinker Board
and the Tinker Board S board.
* Fix Tinker Board S (eMMC) boot (#650)
Use Tinker Board S U-Boot configuration which is capable to boot from
eMMC as well as from SD card.
Note that this makes U-Boot always claiming to run on Tinker Board S:
..
Model: Rockchip RK3288 Asus Tinker Board S
..
It seems that there is no generic Tinker Board configuration. However,
Tinker Board S configuration really seems to work well with Tinker Board
as well, so just use it.
Also today the U-Boot Makefile seems to generate a working idbloader.img
already. Drop our special handling.
* Use Tinker Board S device tree if booting from eMMC for Linux
Instead of patching the Tinker Board device tree, select the device tree
based on what device we are booting from.
Note: This boots the non-S device tree when booting a Tinker Board S
from SD card! But there is no reliable detection otherwise, so let's
just live with that fact.
* Document how to use our U-Boot to flash eMMC
