* Make sure to set board_rev for N2+ correctly
For some reason the code to set the environment did not make it into the
ODROID N2 board code. Fix the patch to correctly set board_rev for N2(+).
Also remove the w400 patch as it is no longer required.
* Use latest ODROID-N2+ patches
Use the queued patches (and fixes) for upstream ODROID-N2+ support.
This uses the clock settings from meson-g12b-a311d.dtsi running the
CPUs at the following clocks:
- 4xA73@2.2GHz
- 2xA53@1.8GHz
Instead of reverting the CDC ACM cool-down patch fix the intention of
that change. This should fix the error recovery paths in the CDC ACM
driver and allow CDC ACM devices to continue working even in the event
of USB issues.
Revert CDC ACM cool-down patch. This should fix the error recovery paths
in the CDC ACM driver and allow CDC ACM devices to continue working even
in the event of USB issues.
* Bump ODROID boards to Linux 5.9.1
This makes quite some patches obsolete which since have been upstreamed.
* Drop Linux 5.7 header symbols
Since we do not introduce new packages which actually require a newer
kernel headers, there is no value in having config symbols for the new
kernel version. Buildroot is still using the headers from our kernel,
and hence gets the latest version of the headers.
The patch causes U-Boot freezes in some configurations. The root cause
is that U-Boot does not allow to use the bss section in pre-relocation
code (which is where the UART is used). Drop the patch as it is not
required currently.
See also:
http://u-boot.10912.n7.nabble.com/RPi4-U-Boot-freeze-td424432.html#a427198
The to symlink serial0/1 currently might apply to the first or second
ttyAMAX instance. In downstream, a patch makes sure that the first
PL011 is always ttyAMA0. However, upstream the numbering depends on the
UART alias, which leads to the first PL011 being ttyAMA1.
Check the actual iobase too to make sure we are dealing with the first
PL011 instance.
See also:
05cfe136f7 (diff-2678c183f503319c8d8c09c818af789a)
* Remove rk3288-xt-q8l-v10.dts related patches
We only support ASUS Tinker Board, so no need for those patches.
* Remove unnecessary patches and rebase some for Tinker Board S
Some patches only apply to the Tinker Board device tree. Rebase them to
apply to the dtsi file so they apply for both boards, the Tinker Board
and the Tinker Board S board.
* Fix Tinker Board S (eMMC) boot (#650)
Use Tinker Board S U-Boot configuration which is capable to boot from
eMMC as well as from SD card.
Note that this makes U-Boot always claiming to run on Tinker Board S:
..
Model: Rockchip RK3288 Asus Tinker Board S
..
It seems that there is no generic Tinker Board configuration. However,
Tinker Board S configuration really seems to work well with Tinker Board
as well, so just use it.
Also today the U-Boot Makefile seems to generate a working idbloader.img
already. Drop our special handling.
* Use Tinker Board S device tree if booting from eMMC for Linux
Instead of patching the Tinker Board device tree, select the device tree
based on what device we are booting from.
Note: This boots the non-S device tree when booting a Tinker Board S
from SD card! But there is no reliable detection otherwise, so let's
just live with that fact.
* Document how to use our U-Boot to flash eMMC
Remove code duplication and make sure to load socinfo only once. Also
set board_rev before MAC address to make sure board_rev is set even if
loading MAC address from efuses fails.
* Add ODROID-N2+ support
Add ODROID-N2+ support with the new SoC revision c. Extend the U-Boot
script: Assume ODROID-N2 if the SoC revision is "a" (there are only "a"
revision SoCs on ODROID N2) and assume N2+ otherwise.
Currently using overclock mode as proposed in the upstream kernel patches.
* Update hassos-hook.sh
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
* Backport USB PCIe/XHCI patches to U-Boot 2020.07
Backport relevant patches required to make PCIe/USB XHCI work.
* Backport/integrate PCIe device tree changes from upstream Linux
U-Boot uses the device tree provided by upstream Linux. Make sure the
device tree has the relevant chanages to make VL805 USB controller
reset work.
* Document RPi 4 USB mass storage support (#746)
