* Linux: Update kernel 5.10.61 for ODROID-N2 (#1512)
Update the kernel to 5.10.61 for ODROID-N2 and fix the update script
to update kernel for ODROID-N2 next time too.
* Move ODROID kernel patches to non-kernel version specific directory
Don't fail adding reserved memory when a memory region already has been
reserved (e.g. via memreserve). This avoids conflicting no-map setting
and makes sure memory is properly reserved.
* Add squashfs with LZ4 and LZO compression to Barebox
* Add squashfs with LZO compression to U-Boot
* Use "raw" as type for kernel partition which is compatible with ext4
image as well as squashfs.
Note: This does not use squashfs for the kernel but merly adds support
for it. This will allow to downgrade/fallback to the non-squashfs
version. Using squashfs for the kernel partition is implemented in dev
(for release 7).
The patches for ODROID-C2/C4 don't apply to Linux 5.12 used in
ODROID-N2. Move ODROID-C2/C4 patches to kernel version specific
directory so they don't get applied for ODROID-N2.
(cherry picked from commit 64d3cd88a1)
For ODROID-N2, release 6 is using Linux 5.9.16. On dev branch we most
likely will move to latest stable and skip 5.10. Drop those unnecessary
patches.
(cherry picked from commit f7c5154bda)
It seems that the TPU (thermal monitoring) sometimes reports
unreasonable high temperatures, leading the kernel to trigger a thermal
shutdown. Add a patch which filters out such spurious temperature
readings.
Since the move to 5.10 multiple users experience stability issues
leading to random crashes. All reboots follow a SError Interrupt:
[48112.247242] SError Interrupt on CPU5, code 0xbf000000 -- SError
...
Revert back to Linux 5.9.16 for now.
It seems that the crash of the Meson DRM driver on shutdown can also be
fixed by compiling it in. The driver is also built-in in LibreELEC,
hence this is better tested by the upstream community.
Note the underlying issue seems to be a disabled clock: Since the
introduction of meson_drv_shutdown some registers are touched at a very
late stage. Those clock get disabled in meson_ee_pwrc_shutdown. It seems
that when the driver is built-in, meson_drv_shutdown gets called before
meson_ee_pwrc_shutdown and hence sidesteps the problem.
Note: This increases the kernel by a bit since DRM needs to be built-in
as well. Configure some less common used file systems as modules
(ext3/NFS).
In Linux 5.10.24 a regression has been introduced which broke reboot on
ODROID-N2(+). Interestingly the patch should improve reboot stability
for VIM3, which uses the same SoC. However, it seems that in the
ODROID-N2 case, this causes more problems then it fixes. Revert the
offending patch.
* Re-add patches missed with U-Boot 2021.04-rc4 upgrade
Also add patches for Raspberry Pi again.
* Regenerate patches for U-Boot 2021.04
* Update to U-Boot 2021.04
Bump to the latest U-Boot release 2021.04-rc4. This alows to drop quite
some patches which have been sent to the mailing list or picked from the
mailing list and have been merged upstream now.
* Add Ralink rt27xx/rt28xx/rt30xx firmware (#1242)
Add Ralink firmware for devices which have the driver enabled. The
firmware's are rather small at 20KiB in total.
* Remove Ralink and other WiFi drivers from Tinker Board
The board has on-board WiFi, no need for Ralink drivers to be enabled.
* Add Ralink WiFi drivers and firmware to ODROID boards
* Drop ODROID specific kernel update script
With the jump to Linux 5.10 LTS we can use the same upstream kernel for
Hardkernel ODROID boards as well. Extend the update-kernel-upstream.sh
to support the ODROID boards.
* Linux: Update kernel 5.10.13
* Add Realtek RTL8812AU out-of-tree driver
This adds support for Realtek RTL8812AU devices such as the Hardkernel
WiFi Module 5A (with the RTL8811AU chipset, supported by this driver as
well). This patch uses Realtek driver 5.9.3.2 which has been made to
compile up to Linux 5.10.
Note: This driver does not seem to support 5GHz networks! But it seems
the only driver which supports the RTL8811AU chipset and also works with
recent mainline drivers...
* Enable RTL8812AU driver for Hardkernel modules
The WiFi Module 5A comes with a RTL8811AU chipset. Enable the driver for
all Hardkernel modules.
* Revert "Fix boot from 128GB Micron eMMC on ODROID-N2(+) (#1064)"
This reverts commit 162084082e.
This patches seem to cause issue on a ODROID-N2 with 32GB eMMC.
* Cap eMMC frequency to 24MHz in U-Boot for ODROID-N2(+)
Also remove the ODROID-C4 specific patch.
Fix ethernet PHY reset timing to make sure the link comes up when
reconfiguring the link.
Also drop 0006-clk-meson-g12a-mark-fclk_div2-as-critical.patch which has
been applied in v5.9.2 stable release.
The version banner was showing "Amlogic Meson G12A (Unknown) Revision
28:0 (0:0)" in all cases instead of the correct SoC name and revision.
Make sure the SoC revision is properly read also for the banner.
The change "Avoid trying to boot non-existing kernel image in failover
case" introduced a broken boot script on Raspberry Pi (when booting from
partition B) and ODROID-XU4.
* Avoid trying to boot non-existing kernel image in fail-over case
The A/B update system automatically switches to the other boot slot when
booting fails. However, in a fresh installation, only boot slot A
exists. If booting fails three times (e.g. if somebody plugs out power
before the slot can be marked as good), then the system switches to boot
slot B which does not contain a kernel image yet. Avoid trying to boot
the non-existing kernel image.
With this change, if slot B is empty U-Boot will restore both slots to 3
attempts and retry booting from slot A on next reboot:
```
Trying to boot slot B, 2 attempts remaining. Loading kernel ...
** Unrecognized filesystem type **
No valid slot found, resetting tries to 3
storing env...
```
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
* Fix N2+ boot by disabling USB enumeration
On some devices USB enumeration in U-Boot seems to freeze:
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... <freeze>
We don't use USB currenty in the U-Boot script, disable it for now.
* Disable USB enumeration on all ODROID devices
After running HAOS on my ODROID N2+ several hours I see freezes and
sometimes stack traces which point to a problem in CPU frequency
scaling. This crash seems not to appear on Hardkernel's 18.04 Ubuntu
stable release. However, Hardkernel's Ubuntu uses the performance
governor. Use the performance governor as well to avoid crashes on N2+.
* Make sure to set board_rev for N2+ correctly
For some reason the code to set the environment did not make it into the
ODROID N2 board code. Fix the patch to correctly set board_rev for N2(+).
Also remove the w400 patch as it is no longer required.
* Use latest ODROID-N2+ patches
Use the queued patches (and fixes) for upstream ODROID-N2+ support.
This uses the clock settings from meson-g12b-a311d.dtsi running the
CPUs at the following clocks:
- 4xA73@2.2GHz
- 2xA53@1.8GHz
Instead of reverting the CDC ACM cool-down patch fix the intention of
that change. This should fix the error recovery paths in the CDC ACM
driver and allow CDC ACM devices to continue working even in the event
of USB issues.
Revert CDC ACM cool-down patch. This should fix the error recovery paths
in the CDC ACM driver and allow CDC ACM devices to continue working even
in the event of USB issues.
* Bump ODROID boards to Linux 5.9.1
This makes quite some patches obsolete which since have been upstreamed.
* Drop Linux 5.7 header symbols
Since we do not introduce new packages which actually require a newer
kernel headers, there is no value in having config symbols for the new
kernel version. Buildroot is still using the headers from our kernel,
and hence gets the latest version of the headers.
Remove code duplication and make sure to load socinfo only once. Also
set board_rev before MAC address to make sure board_rev is set even if
loading MAC address from efuses fails.
