* Move Bluetooth protocol configuration to hassos.config
Enable a couple of potential useful Bluetooth protocol drivers.
Also enable Bluetooth Network Encapsulation Protocol since the BlueZ
plug-in seems to be enabled.
* Drop OverlayFS configuration not liked by Docker
* Enable wext and nl80211 drivers for wpa_supplicant for all devices
* Enable r8188eu module globally and add related firmware to all devices config
Co-authored-by: Stefan Agner <stefan@agner.ch>
* Bump buildroot
* buildroot 73991f0fee...5b5dff3136 (1):
> package/linux-firmware: Add RTL8152/8153/8156 firmware
* Enable Realtek 8152/8153/8156 USB Ethernet adapter support
Enable kernel driver and install firmware for Realtek USB Ethernet
adapter. While at it, also enable some other common USB Ethernet
adapters which don't require firmwares.
CONFIG_BT_HCIBTUSB selects CONFIG_BT_INTEL. That causes CONFIG_BT_INTEL
to be built-in instead of being built as a kernel module.
When the driver is built-in, loading firmware fails during early boot
with the following error message:
[ 1.058941] bluetooth hci0: Direct firmware load for intel/ibt-17-16-1.sfi failed with error -2
Make sure the driver is built as a module which should fix firmware
loading.
* add eq3_char_loop package (eQ-3 char loopback kernel module)
* add generic_raw_uart package (low-latency raw UART kernel driver)
* add rpi-rf-mod package
* add device tree overlay support for RPI-RF-MOD/HM-MOD-RPI-PCB on Raspberry Pi
* enable GPIOLIB and GPIO_SYSFS required for RPI-RF-MOD/HM-MOD-RPI-PCB support.
* add basic RPI-RF-MOD/HM-MOD-RPI-PCB support for ASUS Tinker Board
* add device tree overlay support for ASUS Tinker Board and add
haos-config.txt loading support to U-Boot boot script
* Add SocketCAN support
A Controller Area Network (CAN bus) is a robust vehicle bus standard designed to allow microcontrollers and devices to communicate with each other's applications without a host computer. It is a message-based protocol, designed originally for multiplex electrical wiring within automobiles to save on copper, but it can also be used in many other contexts. For each device, the data in a frame is transmitted sequentially but in such a way that if more than one device transmits at the same time, the highest priority device can continue while the others back off. Frames are received by all devices, including by the transmitting device.
* Update also for GS_USB support
There is a port of the candleLight USB to CAN firmware for CANable. The port works very well under Linux using the gs_usb driver. This firmware does not use slcan, so it is not interchangeable with the stock firmware. However, the CANable appears as a CAN interface natively in Linux
With the candlelight firmware, simply plug in the CANable and the device will enumerate as can0. Set the baud rate and bring the interface up with the following command, and you're good to go!
ip link set can0 up type can bitrate 500000
* Update for Peak PCAN-USB Support
* Update azure-pipelines-release.yml for Azure Pipelines
* Update azure-pipelines-release.yml for Azure Pipelines
* Update azure-pipelines-release.yml for Azure Pipelines
* Fix double LINUX_HEADERS
* Add support for TI USB 3410 or 5052 serial devices (#542)
* Added BT support to device-support.conf file, and removed BT support from kernel.config file
* Removed BT support, as it was moved to device-support.config file
* Added new line at the end of the file
* Changed:
CONFIG_BT_HCIBTUSB from 'm' to 'y'
CONFIG_BT_HCIBTUSB_BCM from 'y' to 'm'
CONFIG_BT_HCIBTUSB_RTL from 'y' to 'm'
* Update device-support.config
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
