* Add Realtek RTL8812AU out-of-tree driver
This adds support for Realtek RTL8812AU devices such as the Hardkernel
WiFi Module 5A (with the RTL8811AU chipset, supported by this driver as
well). This patch uses Realtek driver 5.9.3.2 which has been made to
compile up to Linux 5.10.
Note: This driver does not seem to support 5GHz networks! But it seems
the only driver which supports the RTL8811AU chipset and also works with
recent mainline drivers...
* Enable RTL8812AU driver for Hardkernel modules
The WiFi Module 5A comes with a RTL8811AU chipset. Enable the driver for
all Hardkernel modules.
After increasing the actual disk image size the capacity field in the
OVF description file still was mentioning 6GB. This seems to be
problematic for VMware hypervisor. Increase the size to 32GB as well.
* Revert "Fix boot from 128GB Micron eMMC on ODROID-N2(+) (#1064)"
This reverts commit 162084082e.
This patches seem to cause issue on a ODROID-N2 with 32GB eMMC.
* Cap eMMC frequency to 24MHz in U-Boot for ODROID-N2(+)
Also remove the ODROID-C4 specific patch.
VMware as well as Qemu emulate LSI53C1030 SCSI controller when choosing
a SCSI controller has host interface for disks. For VMware this seems
to be the default choice. Enable the driver by default.
Fix ethernet PHY reset timing to make sure the link comes up when
reconfiguring the link.
Also drop 0006-clk-meson-g12a-mark-fclk_div2-as-critical.patch which has
been applied in v5.9.2 stable release.
The version banner was showing "Amlogic Meson G12A (Unknown) Revision
28:0 (0:0)" in all cases instead of the correct SoC name and revision.
Make sure the SoC revision is properly read also for the banner.
* Add sound card by default using the hdaudio driver (#925)
* Use virtio-net for VirtualBox
The virtio-net driver is a paravirtualization driver which means less
overhead than virtualizing a full network card. The driver is supported
by VirtualBox since several releases by now.
* Use full OS name in product name.
The change "Avoid trying to boot non-existing kernel image in failover
case" introduced a broken boot script on Raspberry Pi (when booting from
partition B) and ODROID-XU4.
* Add 2020-10-28 beta EEPROM
This improves boot from USB and speeds up boot times.
also includes sd card v1 boot reliability.
see https://github.com/raspberrypi/rpi-eeprom/pull/246
Also add HDMI_DELAY=0 so HDMI display is always visible
for easier debugging.
* Avoid trying to boot non-existing kernel image in fail-over case
The A/B update system automatically switches to the other boot slot when
booting fails. However, in a fresh installation, only boot slot A
exists. If booting fails three times (e.g. if somebody plugs out power
before the slot can be marked as good), then the system switches to boot
slot B which does not contain a kernel image yet. Avoid trying to boot
the non-existing kernel image.
With this change, if slot B is empty U-Boot will restore both slots to 3
attempts and retry booting from slot A on next reboot:
```
Trying to boot slot B, 2 attempts remaining. Loading kernel ...
** Unrecognized filesystem type **
No valid slot found, resetting tries to 3
storing env...
```
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
* Fix N2+ boot by disabling USB enumeration
On some devices USB enumeration in U-Boot seems to freeze:
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... <freeze>
We don't use USB currenty in the U-Boot script, disable it for now.
* Disable USB enumeration on all ODROID devices
The current default size of 6GB can fill up pretty quickly. Since most
disk images we offer resize dynamically its not really problem to ship
with a bigger default size. It avoids support cases when people forget
to increase the disk image size.
* Use double quote to prevent globbing and exit with error in case
directory doesn't exit in hassos-hook.sh
* echo flags are undefined in POSIX, use bash instead in
bluetooth-rtl8723
* Bump Raspberry Pi kernel to 5.4
Bump kernel to the downstream Raspberry Pi 5.4 kernel. Drop patches
already merged upstream and use rebased patches for USB reset
controller (required for U-Boot 2020.10 for USB SSD boot).
* Add compatible node for upstream U-Boot
Add brcm,bcm2835-pl011 to make upstream U-Boot bind with the
bcm283x_pl011 driver. This allows to boot with the device tree provided
by the Raspberry Pi Linux kernel 5.4 even without enable_uart=1.
After running HAOS on my ODROID N2+ several hours I see freezes and
sometimes stack traces which point to a problem in CPU frequency
scaling. This crash seems not to appear on Hardkernel's 18.04 Ubuntu
stable release. However, Hardkernel's Ubuntu uses the performance
governor. Use the performance governor as well to avoid crashes on N2+.
This reverts commit c92b4b54be.
Pure GPT would be nice, but older EEPROM/firmware version seem not to
handle it properly (before EEPROM 2020-09-03/firmware 2020-10-22). Since
devices still get shipped with older EEPROM we currently moving to pure
GPT would make those devices not booting.
Stick with hybrid mode for now to make sure HAOS boots on all devices no
matter if a new or old EEPROM is in use.
* Make sure to set board_rev for N2+ correctly
For some reason the code to set the environment did not make it into the
ODROID N2 board code. Fix the patch to correctly set board_rev for N2(+).
Also remove the w400 patch as it is no longer required.
* Use latest ODROID-N2+ patches
Use the queued patches (and fixes) for upstream ODROID-N2+ support.
This uses the clock settings from meson-g12b-a311d.dtsi running the
CPUs at the following clocks:
- 4xA73@2.2GHz
- 2xA53@1.8GHz
Instead of reverting the CDC ACM cool-down patch fix the intention of
that change. This should fix the error recovery paths in the CDC ACM
driver and allow CDC ACM devices to continue working even in the event
of USB issues.
Revert CDC ACM cool-down patch. This should fix the error recovery paths
in the CDC ACM driver and allow CDC ACM devices to continue working even
in the event of USB issues.
* Bump ODROID boards to Linux 5.9.1
This makes quite some patches obsolete which since have been upstreamed.
* Drop Linux 5.7 header symbols
Since we do not introduce new packages which actually require a newer
kernel headers, there is no value in having config symbols for the new
kernel version. Buildroot is still using the headers from our kernel,
and hence gets the latest version of the headers.
The patch causes U-Boot freezes in some configurations. The root cause
is that U-Boot does not allow to use the bss section in pre-relocation
code (which is where the UART is used). Drop the patch as it is not
required currently.
See also:
http://u-boot.10912.n7.nabble.com/RPi4-U-Boot-freeze-td424432.html#a427198
The to symlink serial0/1 currently might apply to the first or second
ttyAMAX instance. In downstream, a patch makes sure that the first
PL011 is always ttyAMA0. However, upstream the numbering depends on the
UART alias, which leads to the first PL011 being ttyAMA1.
Check the actual iobase too to make sure we are dealing with the first
PL011 instance.
See also:
05cfe136f7 (diff-2678c183f503319c8d8c09c818af789a)
* Remove rk3288-xt-q8l-v10.dts related patches
We only support ASUS Tinker Board, so no need for those patches.
* Remove unnecessary patches and rebase some for Tinker Board S
Some patches only apply to the Tinker Board device tree. Rebase them to
apply to the dtsi file so they apply for both boards, the Tinker Board
and the Tinker Board S board.
* Fix Tinker Board S (eMMC) boot (#650)
Use Tinker Board S U-Boot configuration which is capable to boot from
eMMC as well as from SD card.
Note that this makes U-Boot always claiming to run on Tinker Board S:
..
Model: Rockchip RK3288 Asus Tinker Board S
..
It seems that there is no generic Tinker Board configuration. However,
Tinker Board S configuration really seems to work well with Tinker Board
as well, so just use it.
Also today the U-Boot Makefile seems to generate a working idbloader.img
already. Drop our special handling.
* Use Tinker Board S device tree if booting from eMMC for Linux
Instead of patching the Tinker Board device tree, select the device tree
based on what device we are booting from.
Note: This boots the non-S device tree when booting a Tinker Board S
from SD card! But there is no reliable detection otherwise, so let's
just live with that fact.
* Document how to use our U-Boot to flash eMMC
Remove code duplication and make sure to load socinfo only once. Also
set board_rev before MAC address to make sure board_rev is set even if
loading MAC address from efuses fails.
