* Add Realtek RTL8812AU out-of-tree driver
This adds support for Realtek RTL8812AU devices such as the Hardkernel
WiFi Module 5A (with the RTL8811AU chipset, supported by this driver as
well). This patch uses Realtek driver 5.9.3.2 which has been made to
compile up to Linux 5.10.
Note: This driver does not seem to support 5GHz networks! But it seems
the only driver which supports the RTL8811AU chipset and also works with
recent mainline drivers...
* Enable RTL8812AU driver for Hardkernel modules
The WiFi Module 5A comes with a RTL8811AU chipset. Enable the driver for
all Hardkernel modules.
* Revert "Fix boot from 128GB Micron eMMC on ODROID-N2(+) (#1064)"
This reverts commit 162084082e.
This patches seem to cause issue on a ODROID-N2 with 32GB eMMC.
* Cap eMMC frequency to 24MHz in U-Boot for ODROID-N2(+)
Also remove the ODROID-C4 specific patch.
Fix ethernet PHY reset timing to make sure the link comes up when
reconfiguring the link.
Also drop 0006-clk-meson-g12a-mark-fclk_div2-as-critical.patch which has
been applied in v5.9.2 stable release.
The version banner was showing "Amlogic Meson G12A (Unknown) Revision
28:0 (0:0)" in all cases instead of the correct SoC name and revision.
Make sure the SoC revision is properly read also for the banner.
The change "Avoid trying to boot non-existing kernel image in failover
case" introduced a broken boot script on Raspberry Pi (when booting from
partition B) and ODROID-XU4.
* Avoid trying to boot non-existing kernel image in fail-over case
The A/B update system automatically switches to the other boot slot when
booting fails. However, in a fresh installation, only boot slot A
exists. If booting fails three times (e.g. if somebody plugs out power
before the slot can be marked as good), then the system switches to boot
slot B which does not contain a kernel image yet. Avoid trying to boot
the non-existing kernel image.
With this change, if slot B is empty U-Boot will restore both slots to 3
attempts and retry booting from slot A on next reboot:
```
Trying to boot slot B, 2 attempts remaining. Loading kernel ...
** Unrecognized filesystem type **
No valid slot found, resetting tries to 3
storing env...
```
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
* Fix N2+ boot by disabling USB enumeration
On some devices USB enumeration in U-Boot seems to freeze:
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... <freeze>
We don't use USB currenty in the U-Boot script, disable it for now.
* Disable USB enumeration on all ODROID devices
After running HAOS on my ODROID N2+ several hours I see freezes and
sometimes stack traces which point to a problem in CPU frequency
scaling. This crash seems not to appear on Hardkernel's 18.04 Ubuntu
stable release. However, Hardkernel's Ubuntu uses the performance
governor. Use the performance governor as well to avoid crashes on N2+.
* Make sure to set board_rev for N2+ correctly
For some reason the code to set the environment did not make it into the
ODROID N2 board code. Fix the patch to correctly set board_rev for N2(+).
Also remove the w400 patch as it is no longer required.
* Use latest ODROID-N2+ patches
Use the queued patches (and fixes) for upstream ODROID-N2+ support.
This uses the clock settings from meson-g12b-a311d.dtsi running the
CPUs at the following clocks:
- 4xA73@2.2GHz
- 2xA53@1.8GHz
Instead of reverting the CDC ACM cool-down patch fix the intention of
that change. This should fix the error recovery paths in the CDC ACM
driver and allow CDC ACM devices to continue working even in the event
of USB issues.
Revert CDC ACM cool-down patch. This should fix the error recovery paths
in the CDC ACM driver and allow CDC ACM devices to continue working even
in the event of USB issues.
* Bump ODROID boards to Linux 5.9.1
This makes quite some patches obsolete which since have been upstreamed.
* Drop Linux 5.7 header symbols
Since we do not introduce new packages which actually require a newer
kernel headers, there is no value in having config symbols for the new
kernel version. Buildroot is still using the headers from our kernel,
and hence gets the latest version of the headers.
Remove code duplication and make sure to load socinfo only once. Also
set board_rev before MAC address to make sure board_rev is set even if
loading MAC address from efuses fails.
* Add ODROID-N2+ support
Add ODROID-N2+ support with the new SoC revision c. Extend the U-Boot
script: Assume ODROID-N2 if the SoC revision is "a" (there are only "a"
revision SoCs on ODROID N2) and assume N2+ otherwise.
Currently using overclock mode as proposed in the upstream kernel patches.
* Update hassos-hook.sh
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
