By default ConditionFirstBoot is ankered to the presence of
/etc/machine-id. However, in our case /etc/machine-id is a bind mount,
which makes the first boot condition non-working.
Since machine-id is stored by the bootloader on HAOS, use the boot
loaders knowledge and pass the information to systemd.
* Support custom sized SPL/raw boot region
This is required for Rockchip which by default stores the U-Boot FIT
image at the 8MiB offset.
* Ignore shellcheck warning
The new systemd version v252 brings a new naming scheme, in particular
it seems that on device tree based systems (e.g. Raspberry Pis) the
Ethernet device name changes from eth0 to end0.
This breaks a previously made configuration.
Even worse, it seems that the default NetworkManager behavior is to only
configure a network device if there is no profile. But since profiles
are configured on a typical installation, NetworkManager doesn't bring
up any of the network interface, leaving the user stranded on an
unconnected system.
Ideally, we should have a plan how to migrate from one naming scheme to
the next. For now, just stick with the naming scheme HAOS 9.x has been
using.
* Linux: Update kernel 6.1.12
* Update generic_raw_uart to build with Linux 6.1
* Update Realtek rtl8821cu/rtl88x2bu to build with Linux 6.1
* Bump buildroot
* buildroot 43f82f01b9...90aa1a6daa (1):
> rtl8812au-aircrack-ng: bump to latest rev d98018
* Fix eq3_char_loop to build with Linux 6.1
* rtl8821cu: make sure -Werror is disabled for the kernel build
* generic_raw_uart: make sure -Werror is disabled for the kernel build
The ODROID-XU4 is largely compatible with the ODROID-HC1. It seems that
the image used to work until recently, where a stable kernel update
broke access to the S-ATA disk.
Revert the offending stable kernel patch to fix S-ATA disk on
ODROID-HC1.
The cgroup_enable parameter is a Raspberry Pi kernel specific kernel
parameter. Upstream based kernel do not have the parameter, and hence
do not do anything.
This gets rid of the following message during boot:
Unknown kernel command line parameters "cgroup_enable=memory", will be passed to user space.
* Remove duplicate config.txt copy statement
* Use static cmdline.txt file
Instead of dynamically creating cmdline.txt use a static version of it.
This aligns with other boot loader/firmware configuration files and makes
it easier to customize the file per board.
* Add squashfs with LZ4 and LZO compression to Barebox
* Add squashfs with LZO compression to U-Boot
* Use squashfs for Linux kernel partition
Generate a squashfs image with LZO compression for the Linux kernel
partition. Adjust the boot scripts to be file system independent commands
to boot from squashfs.
It seems that the TPU (thermal monitoring) sometimes reports
unreasonable high temperatures, leading the kernel to trigger a thermal
shutdown. Add a patch which filters out such spurious temperature
readings.
The change "Avoid trying to boot non-existing kernel image in failover
case" introduced a broken boot script on Raspberry Pi (when booting from
partition B) and ODROID-XU4.
* Avoid trying to boot non-existing kernel image in fail-over case
The A/B update system automatically switches to the other boot slot when
booting fails. However, in a fresh installation, only boot slot A
exists. If booting fails three times (e.g. if somebody plugs out power
before the slot can be marked as good), then the system switches to boot
slot B which does not contain a kernel image yet. Avoid trying to boot
the non-existing kernel image.
With this change, if slot B is empty U-Boot will restore both slots to 3
attempts and retry booting from slot A on next reboot:
```
Trying to boot slot B, 2 attempts remaining. Loading kernel ...
** Unrecognized filesystem type **
No valid slot found, resetting tries to 3
storing env...
```
Co-authored-by: Pascal Vizeli <pascal.vizeli@syshack.ch>
* Fix N2+ boot by disabling USB enumeration
On some devices USB enumeration in U-Boot seems to freeze:
starting USB...
Bus usb@ff500000: Register 3000140 NbrPorts 3
Starting the controller
USB XHCI 1.10
scanning bus usb@ff500000 for devices... <freeze>
We don't use USB currenty in the U-Boot script, disable it for now.
* Disable USB enumeration on all ODROID devices
