* add eq3_char_loop package (eQ-3 char loopback kernel module)
* add generic_raw_uart package (low-latency raw UART kernel driver)
* add rpi-rf-mod package
* add device tree overlay support for RPI-RF-MOD/HM-MOD-RPI-PCB on Raspberry Pi
* enable GPIOLIB and GPIO_SYSFS required for RPI-RF-MOD/HM-MOD-RPI-PCB support.
* add basic RPI-RF-MOD/HM-MOD-RPI-PCB support for ASUS Tinker Board
* add device tree overlay support for ASUS Tinker Board and add
haos-config.txt loading support to U-Boot boot script
* Re-add patches missed with U-Boot 2021.04-rc4 upgrade
Also add patches for Raspberry Pi again.
* Regenerate patches for U-Boot 2021.04
* Update to U-Boot 2021.04
* Add udisks2 package
Add latest release of udisks2 as a package. Also disable polkit to avoid
excessive dependencies.
* Add udisks2 and os-agent to Home Assistant OS
* Bump OS Agent to latest version with udisks support
* Add RTL87xx/RTL88xx Bluetooth firmware
Enable Realtek Bluetooth dongles by adding firmware for RTL87xx and
RTL8xx devices.
* Enable Wireless firmwares for OVA and Generic x86-64 machines
Virtual machines might use hardware pass through functionality to get
direct access to wireless hardware. Add all firmwares we use in Generic
x86-64 image also to the OVA image. Also enable Ralink devices for the
two machines.
* Add RTL87xx/RTL88xx Bluetooth firmwares (#1273)
Add RTL87xx/RTL88xx Bluetooth to all devices without on-board Bluetooth.
Bump to the latest U-Boot release 2021.04-rc4. This alows to drop quite
some patches which have been sent to the mailing list or picked from the
mailing list and have been merged upstream now.
* Rebase patches to Buildroot 2021.02-rc3
* Update Buildroot to 2021.02-rc3
* Declare Kernel headers to be Linux version 5.10 (since they are, and new Buildroot knows about 5.10)
* Add Ralink rt27xx/rt28xx/rt30xx firmware (#1242)
Add Ralink firmware for devices which have the driver enabled. The
firmware's are rather small at 20KiB in total.
* Remove Ralink and other WiFi drivers from Tinker Board
The board has on-board WiFi, no need for Ralink drivers to be enabled.
* Add Ralink WiFi drivers and firmware to ODROID boards
* Drop ODROID specific kernel update script
With the jump to Linux 5.10 LTS we can use the same upstream kernel for
Hardkernel ODROID boards as well. Extend the update-kernel-upstream.sh
to support the ODROID boards.
* Linux: Update kernel 5.10.13
* Use systemd-growfs instead of resize2fs (#1106)
Since systemd 236 systemd has a built-in file system growing mechanism.
The mechanism relies on the kernels online file system resize
capabilities instead of the external resize2fs utility. Online resizing
is supposedly much faster since the kernel takes care of things.
This also makes sure that external file systems get resized which
previously have not been taken care of.
* Drop HA OS specific file system resizing
Since we have systemd-growfs in place now we can drop our file system
resizing code.
* Make sure /dev/disk/by-label/hassos-data is present after resizing
Note: systemd will retry mnt-data.mount later, so at least in theory
this shouldn't really matter. However, the journal has a lot of churn
due to that reordering.
* Add Realtek RTL8812AU out-of-tree driver
This adds support for Realtek RTL8812AU devices such as the Hardkernel
WiFi Module 5A (with the RTL8811AU chipset, supported by this driver as
well). This patch uses Realtek driver 5.9.3.2 which has been made to
compile up to Linux 5.10.
Note: This driver does not seem to support 5GHz networks! But it seems
the only driver which supports the RTL8811AU chipset and also works with
recent mainline drivers...
* Enable RTL8812AU driver for Hardkernel modules
The WiFi Module 5A comes with a RTL8811AU chipset. Enable the driver for
all Hardkernel modules.
* Revert "Fix boot from 128GB Micron eMMC on ODROID-N2(+) (#1064)"
This reverts commit 162084082e.
This patches seem to cause issue on a ODROID-N2 with 32GB eMMC.
* Cap eMMC frequency to 24MHz in U-Boot for ODROID-N2(+)
Also remove the ODROID-C4 specific patch.
* Rewrite datactl command
Prepare the target partition as part of the datactl command. Rely on
partlabel for the target disk since we are always using GPT on the
target disk. Use systemd and partlabel mechanism to wait and find
the target data disk. Keep using the file system label to identify
the source disk.
Also use e2image instead of raw dd to move data. This should
speed up the processes significantly.
* Fix corner case when reusing same disk again
* Update buildroot-patches for 2020.11-rc1 buildroot
* Update buildroot to 2020.11-rc1
Signed-off-by: Stefan Agner <stefan@agner.ch>
* Don't rely on sfdisk --list-free output
The --list-free (-F) argument does not allow machine readable mode. And
it seems that the output format changes over time (different spacing,
using size postfixes instead of raw blocks).
Use sfdisk json output and calculate free partition space ourselfs. This
works for 2.35 and 2.36 and is more robust since we rely on output which
is meant for scripts to parse.
* Migrate defconfigs for Buildroot 2020.11-rc1
In particular, rename BR2_TARGET_UBOOT_BOOT_SCRIPT(_SOURCE) to
BR2_PACKAGE_HOST_UBOOT_TOOLS_BOOT_SCRIPT(_SOURCE).
* Rebase/remove systemd patches for systemd 246
* Drop apparmor/libapparmor from buildroot-external
* hassos-persists: use /run as directory for lockfiles
The U-Boot tools use /var/lock by default which is not created any more
by systemd by default (it is under tmpfiles legacy.conf, which we no
longer install).
* Disable systemd-update-done.service
The service is not suited for pure read-only systems. In particular the
service needs to be able to write a file in /etc and /var. Remove the
service. Note: This is a static service and cannot be removed using
systemd-preset.
* Disable apparmor.service for now
The service loads all default profiles. Some might actually cause
problems. E.g. the profile for ping seems not to match our setup for
/etc/resolv.conf:
[85503.634653] audit: type=1400 audit(1605286002.684:236): apparmor="DENIED" operation="open" profile="ping" name="/run/resolv.conf" pid=27585 comm="ping" requested_mask="r" denied_mask="r" fsuid=0 ouid=0
Drop AVAHI and use systemd-resolved to announce hostname via mDNS
and LLMNR. Also continue to offer the _workstation._tcp.local service
since it is used by the CoreDNS mDNS plug-in.
