Update buildroot 2020.02.01 (#622)

* Update buildroot 2020.02.01

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>

* Fix LN

* Fix wpa

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>

* Fix lint

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>

* fix-network

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>

* Fix script

Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>

buildroot/board/friendlyarm/nanopi-neo-plus2/extlinux.conf

@@ -0,0 +1,4 @@
+label linux
+  kernel /Image
+  devicetree /sun50i-h5-nanopi-neo-plus2.dtb
+  append console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait

buildroot/board/friendlyarm/nanopi-neo-plus2/genimage.cfg

@@ -0,0 +1,39 @@
+image boot.vfat {
+	vfat {
+		files = {
+			"Image",
+			"sun50i-h5-nanopi-neo-plus2.dtb",
+			"extlinux"
+		}
+	}
+	size = 64M
+}
+
+image sdcard.img {
+	hdimage {
+	}
+
+	partition spl {
+		in-partition-table = "no"
+		image = "sunxi-spl.bin"
+		offset = 8192
+	}
+
+	partition u-boot {
+		in-partition-table = "no"
+		image = "u-boot.itb"
+		offset = 40K
+		size = 1M # 1MB - 40K
+	}
+
+	partition boot {
+		partition-type = 0xC
+		bootable = "true"
+		image = "boot.vfat"
+	}
+
+	partition rootfs {
+		partition-type = 0x83
+		image = "rootfs.ext4"
+	}
+}

buildroot/board/friendlyarm/nanopi-neo-plus2/linux-extras.config

@@ -0,0 +1,10 @@
+# wireless core
+CONFIG_WIRELESS=y
+CONFIG_CFG80211=y
+CONFIG_MAC80211=y
+CONFIG_CFG80211_WEXT=y
+
+# wireless drivers
+CONFIG_WLAN=y
+CONFIG_WLAN_VENDOR_BROADCOM=y
+CONFIG_BRCMFMAC=m

buildroot/board/friendlyarm/nanopi-neo-plus2/post-build.sh

@@ -0,0 +1,4 @@
+#!/bin/sh
+BOARD_DIR="$(dirname $0)"
+
+install -m 0644 -D $BOARD_DIR/extlinux.conf $BINARIES_DIR/extlinux/extlinux.conf

buildroot/board/friendlyarm/nanopi-neo-plus2/readme.txt

@@ -0,0 +1,37 @@
+Intro
+=====
+
+This default configuration will allow you to start experimenting with the
+buildroot environment for the Nanopi NEO Plus2. With the current configuration
+it will bring-up the board, and allow access through the serial console.
+
+Nanopi NEO2 link:
+http://nanopi.io/nanopi-neo-plus2.html
+
+Wiki link:
+http://wiki.friendlyarm.com/wiki/index.php/NanoPi_NEO_Plus2
+
+This configuration uses U-Boot mainline and kernel mainline.
+
+How to build
+============
+
+    $ make friendlyarm_nanopi_neo_plus2_defconfig
+    $ make
+
+Note: you will need access to the internet to download the required
+sources.
+
+How to write the SD card
+========================
+
+Once the build process is finished you will have an image called "sdcard.img"
+in the output/images/ directory.
+
+Copy the bootable "sdcard.img" onto an SD card with "dd":
+
+  $ sudo dd if=output/images/sdcard.img of=/dev/sdX
+  $ sudo sync
+
+Insert the micro SDcard in your Nanopi NEO Plus2 and power it up. The console
+is on the serial line, 115200 8N1.

buildroot/board/friendlyarm/nanopi-neo-plus2/rootfs_overlay/lib/firmware/brcm/brcmfmac43430-sdio.friendlyarm,nanopi-neo-plus2.txt

@@ -0,0 +1,53 @@
+#AP6212_NVRAM_V1.0.1_20160606
+# 2.4 GHz, 20 MHz BW mode
+# The following parameter values are just placeholders, need to be updated.
+manfid=0x2d0
+prodid=0x0726
+vendid=0x14e4
+devid=0x43e2
+boardtype=0x0726
+boardrev=0x1101
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+sromrev=11
+boardflags=0x00404201
+xtalfreq=26000
+nocrc=1
+ag0=255
+aa2g=1
+ccode=ALL
+
+pa0itssit=0x20
+extpagain2g=0
+
+#PA parameters for 2.4GHz, measured at CHIP OUTPUT
+pa2ga0=-168,7161,-820
+AvVmid_c0=0x0,0xc8
+cckpwroffset0=5
+
+# PPR params
+maxp2ga0=90
+txpwrbckof=6
+cckbw202gpo=0x5555
+legofdmbw202gpo=0x77777777
+mcsbw202gpo=0xaaaaaaaa
+
+# OFDM IIR :
+ofdmdigfilttype=7
+# PAPD mode:
+papdmode=2
+
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+
+#OOB parameters
+hostwake=0x40
+hostrdy=0x41
+usbrdy=0x03
+usbrdydelay=100
+deadman_to=0xffffffff
+# muxenab: 0x1 for UART enable, 0x10 for Host awake
+muxenab=0x10
+# CLDO PWM voltage settings - 0x4 - 1.1 volt
+#cldo_pwm=0x4
+glitch_based_crsmin=1